16 Electromagnetism

27 February

Magnetic Shielding

Seng Kwang Tan 16 Electromagnetism, Demonstrations, IP4 14 Magnetism

Materials

  1. Bar magnet
  2. Paper clip (stainless steel)
  3. Plastic clipboard
  4. Steel bookend

Procedure

  1. Before the demonstration, make sure that the paper clip is not already magnetised by touching it with the steel bookend. If it gets attracted to the bookend, get a new paper clip.
  2. For the demonstration, first show that the paper clip can be picked up by a bar magnet in direct contact.
  3. Next, place the bar magnet on the plastic clipboard and try to pick up the paper clip with the clipboard in between them. Show the audience that the paper clip is attracted.
  4. Finally, place the bar magnet on the steel bookend and attempt to pick up the paper clip with the bookend between them. The paper clip will not be picked up.

Science Explained

Iron and steel are examples of ferromagnetic materials that have their magnetic domains aligned with an external magnetic field when placed in that field. This strengthens the magnetic field but also serves to concentrate the field lines within the ferromagnetic material itself, such that very little of the magnetic field penetrates the “shield”.

 

25 February

Homopolar Motor 2

Seng Kwang Tan 16 Electromagnetism, Demonstrations, IP4 15 Electromagnetism

This video demonstrates how a simple homopolar motor is made using a screw and a small neodymium magnet. The simplest possible motor one can make, it can be used to teach concepts at various levels. For lower secondary students, they can learn about conversion of energy forms while upper secondary students can learn about magnetic forces and Fleming’s left-hand rule.

Materials

  1. 10 cm wire
  2. 1.5 V battery
  3. iron screw
  4. neodymium magnet

Procedure

  1. Attach the neodymium magnet to the head of the screw.
  2. Attach the tip of the screw to one end of the battery such that the screw hangs below the battery. The screw will remain attached to the battery as the magnetic force from the neodymium holds them together.
  3. Hold one end of the wire on the top terminal of the battery and allow the other end of the wire to touch the side of the screw or the magnet. Watch the screw spin.

(Link: Alternative design for the homopolar motor)

16 February

Electromagnetism Lecture

Seng Kwang Tan 16 Electromagnetism, Blog

I enjoy lecturing on topics like Superposition and Electromagnetism in the GCE A-level syllabus as they lend themselves well to the use of fun demonstrations that I can perform in front of the audience.

One of the recent demonstrations that I did was to demonstrate the measurement of the magnetic force acting on a wire and to show that the force can be inverted when the current is reversed. The magnitude of the force can be shown to be consistent with the relationship $$F = BIl \sin \theta$$, where $B$ is the magnetic flux density, $I$ is the current within the wire, $l$ is the length of the wire and $\theta$ is the angle between the wire and the magnetic field. This can be illustrated by independently varying one of the 4 variables and observing the change in force.

The setup is also a good for a demonstration to illustrate Fleming’s Left-Hand Rule.

Meanwhile, here’s a video I made to show what I did:

16 February

Measuring the Force on a Current-Carrying Conductor

Seng Kwang Tan 16 Electromagnetism, Demonstrations

The force acting on a current-carrying conductor is given by $$F =BIl sin \theta$$ where B is the magnetic flux density, I is the current, l is the length of the wire and $\theta$ is the angle between the current and the magnetic field. It can be measured in directly using a weighing scale as described below:

Materials

  1. An electronic weighing scale
  2. Two neodymium magnets
  3. Plasticine
  4. Batteries
  5. 40 cm long wire

Procedure

  1. Place some plasticine between two neodymium magnets to hold them together with each magnet having a different pole facing up (north for one and south for the other).
  2. Place the magnets on the weighing scale.
  3. Connect the 40 cm wire across the opposite terminals of the batteries.
  4. Hold the wire horizontally and place it between the two magnets so that the current runs perpendicularly to the magnetic field lines.
  5. Using Fleming’s left-hand rule, one can predict whether the measured weight will increase or decrease. If the magnetic force acting on the wire is upward, by Newton’s 3rd law, the reaction force acting on the magnets is downward and the measured weight will increase, and vice versa.
  6. Flipping the current around in the opposite direction will yield opposite results.
04 January

Homopolar Motor 1

Seng Kwang Tan 16 Electromagnetism, Demonstrations, Featured

A homopolar motor is a simple electric motor that does not require the use of a commutator. The electric current flows in a fixed direction within the wires of the motor. The following are instructions on how to construct this simple teaching tool that can be used to demonstrate how a motor works, as well as teach concepts such as Fleming’s left-hand rule and $$\mathbf{F}= I\mathbf{l \times B}$$.

Materials

  1. Copper wire (about 22 cm)
  2. Small neodymium magnets (1 or 2)
  3. 1.5 V AA-size battery
  4. Base with either another magnet or a iron surface, such as the head of an iron nail

Procedure

  1. Make a V-shaped bend in the middle of the copper wire, with about 0.5 cm on both sides of the V-shape. Bend the copper wire into a rectangular loop using the dimensions shown below. Homopolar Motor Diagram
  2. Tip: You may use the edge of a wooden block as a guide to bend the copper wires at right angles. A pair of wooden blocks can also be used to flatten the rectangular loop if you press them together tightly with the loop in between.
  3. Mount the neodymium magnet(s) onto the magnet or iron base.
  4. Hook the wires at the base around the magnets.
  5. Place the AA-sized battery with the protruding end on the magnet(s).
  6. Complete the electric circuit by placing the V-shaped end of the rectangular loop onto the flat end of the battery and watch the loop spin.
  7. Be careful not to keep the current flowing for too long as the battery and wire can get very hot.

Science Explained

  1. A force acts on a current if it is placed in a magnetic field. This force is what causes the motor to spin about its axis.
  2. To apply Fleming’s left hand rule, observe from the diagram below how the magnetic field bends around the magnet and its direction with respect to the direction of current flow. How do you think the loop will spin?homopolar motor field lines

If you are having difficulty making this version of the homopolar motor, try the other design for the homopolar motor made using a screw.

02 November

Electromagnet

Seng Kwang Tan 16 Electromagnetism, Demonstrations, IP4 15 Electromagnetism

Materials

  1. Insulated wire (about 1 m in length)
  2. Iron nail (at least 5 cm in length)
  3. 1.5 V battery
  4. Adhesive tape
  5. Small metal paper clip

Procedure

  1. Test that the iron nail is not already magnetised by trying to pick up the metal paper clip with it.
  2. Strip the two ends of the wire off its insulation. Leave about 1 cm bare on each end.
  3. Coil the wire around the iron nail, pushing each coil tightly together, to make a solenoid. Make sure you leave about 5 cm free at each end of the wire in order to connect the battery to the solenoid.
  4. If there is excess wire, make a second layer of coils around the first layer.
  5. Connect the ends of the wire to the terminals of the battery.
  6. Test the solenoid now by picking up the paper clip.