IP Topics

29 March

Egg out of Flask

Seng Kwang Tan 08 Temperature and Ideal Gases, Demonstrations, IP3 05 Density and Pressure

In a previous demonstration, we put a boiled egg into a flask with a mouth narrower than the egg. The challenge is now to remove the egg from the flask without breaking it.

Materials

  1. Flask
  2. Egg
  3. Water
  4. Bunsen burner or candle

Procedure

  1. Pour some water into the conical flask.
  2. Invert the flask quickly over a tray such that the egg seals the mouth of the flask, preventing the water from coming out.
  3. Light a flame and place the part of the flask with water over the flame. This will help prevent the heat from cracking the flask.
  4. Place a tray under the mouth of the flask as the egg slides out to prevent a mess.

Explanation

The flame heats up the air and the water in the flask. The heated air expands while some of the water vapourizes. With the increase in amount of gas and temperature, the pressure within the flask increases.

29 March

Egg into Flask

Seng Kwang Tan 08 Temperature and Ideal Gases, Demonstrations, IP3 05 Density and Pressure

This classic physics demonstration is used to show the effects of pressure difference between the atmosphere and a cooling volume of air. With a set of clean apparatus, you can even have the egg for a snack after that.

Materials

  1. Hard-boiled Egg
  2. Flask or glass bottle with mouth smaller than the egg
  3. Paper measuring about 2 cm by 5 cm
  4. Lighter

Procedure

  1. Peel the hard-boiled egg.
  2. Light the piece of paper and drop it into the flask.
  3. Place the peeled egg on the mouth of the flask such that the egg seals the flask.
  4. Observe the egg being sucked in while the flame dies.

Explanation

When the burning paper enters the flask, it causes the air within the flask to heat up and expand, with some escaping from the flask. When the egg seals the flask, the flame dies as the paper is about to be burned up while oxygen is also running out.

The air then cools down and the pressure within the flask drops. The pressure due to the atmosphere acting downward on the egg is then greater than that acting upward due to the pressure of the cooling air. This pushes the egg into the bottle.

28 February

Ionisation of Air to Remove Static Electric Charges

Seng Kwang Tan 13 Electric Fields, Demonstrations, IP4 10 Static Electricity

Materials

  1. Wool
  2. PVC pipe or plastic comb
  3. String
  4. Lighter

Procedure

  1. Hang the string from an elevated position. Leave the bottom end free.
  2. Rub the PVC pipe with wool. This deposits negative charges, or electrons, onto the surface of the PVC pipe.
  3. Place the side of the pipe that is rubbed near the string. You should notice the string being attracted  towards the PVC pipe.
  4. Holding the PVC pipe still while attracting the string, light a flame using the lighter and place it in between the string and pipe. You should observe the string falling back to its original position.

Science Explained

When air is ionised with the help of a flame, it serves as a conducting medium through which static electric charges can escape from a surface.

27 February

Magnetic Shielding

Seng Kwang Tan 16 Electromagnetism, Demonstrations, IP4 14 Magnetism

Materials

  1. Bar magnet
  2. Paper clip (stainless steel)
  3. Plastic clipboard
  4. Steel bookend

Procedure

  1. Before the demonstration, make sure that the paper clip is not already magnetised by touching it with the steel bookend. If it gets attracted to the bookend, get a new paper clip.
  2. For the demonstration, first show that the paper clip can be picked up by a bar magnet in direct contact.
  3. Next, place the bar magnet on the plastic clipboard and try to pick up the paper clip with the clipboard in between them. Show the audience that the paper clip is attracted.
  4. Finally, place the bar magnet on the steel bookend and attempt to pick up the paper clip with the bookend between them. The paper clip will not be picked up.

Science Explained

Iron and steel are examples of ferromagnetic materials that have their magnetic domains aligned with an external magnetic field when placed in that field. This strengthens the magnetic field but also serves to concentrate the field lines within the ferromagnetic material itself, such that very little of the magnetic field penetrates the “shield”.

 

26 February

Heat Capacity of Water

Seng Kwang Tan 09 First Law of Thermodynamics, Demonstrations, IP4 18 Thermal Properties of Matter

Water has a high specific heat capacity of about 4200 J kg-1 K-1. When a little bit of water is placed in a balloon, it is able to absorb a significant amount of heat from a candle flame and hence prevent the balloon from bursting.
Materials
  1. Two balloons
  2. Two candles
  3. Lighter
Procedure
  1. In this demonstration, one balloons is filled with about 3 tablespoons of water and then inflated.
  2. Another balloon is inflated to the same size as the first to serve as a control.
  3. Both balloons are then placed vertically over two identical candles. Adjust the balloons such that the distance from balloon to candle is the same for both setups. You can use retort stands to clamp the balloons in place if you have them.
  4. Light the candles with the balloons temporarily removed. The flames will have to touch the bottom of the balloon when they are placed back over the candles.
  5. Observe the balloon without water burst first.
  6. The air gushing out from the exploding balloon may put out the other candle.
  7. If you like, you can keep the balloon with water over the flame for a longer duration. The balloon still will not burst until a long time later.
25 February

Homopolar Motor 2

Seng Kwang Tan 16 Electromagnetism, Demonstrations, IP4 15 Electromagnetism

This video demonstrates how a simple homopolar motor is made using a screw and a small neodymium magnet. The simplest possible motor one can make, it can be used to teach concepts at various levels. For lower secondary students, they can learn about conversion of energy forms while upper secondary students can learn about magnetic forces and Fleming’s left-hand rule.

Materials

  1. 10 cm wire
  2. 1.5 V battery
  3. iron screw
  4. neodymium magnet

Procedure

  1. Attach the neodymium magnet to the head of the screw.
  2. Attach the tip of the screw to one end of the battery such that the screw hangs below the battery. The screw will remain attached to the battery as the magnetic force from the neodymium holds them together.
  3. Hold one end of the wire on the top terminal of the battery and allow the other end of the wire to touch the side of the screw or the magnet. Watch the screw spin.

(Link: Alternative design for the homopolar motor)